Instruction List - Type

Contact

Instruction	Type of Input	Note
LD	LD (S)	Takes ON/OFF Data For a Contact Of One Circuit AS Operation Result.
LDI	LDI (S)	Takes ON/OFF Data For b Contact Of One Circuit As Operation Result.
LDP	LDP (S)	If Input Condition Is ON From OFF, Sets For One Scan.
LDF	LDF (S)	If Input Condition Is OFF From ON, Sets For One Scan.
AND	AND (S)	AND-Operates Contact a Of The Assigned Contact And Connected Contants In Series, And Takes The Result As Operation Result.
ANDI	ANDI (S)	AND-Operates Contact b Of The assigned Contact And The Connected Contact In Series, Takes The Result As Operation Result.
ANDF	ANDF (S)	If Input Condition To Contact To Detect Connection In Series Is Off From On, Device S Is Set For One Scan.
ANDP	ANDP (S)	If Input Condition To Contact To Detect Connection In Series Is On From Off, Device S Is Set For One Scan.
OR	OR (S)	OR-Operates a Contact Of The Assigned Contact And The Connected Contact In Parallel And Takes The Result As Operation Result.
ORI	ORI (S)	OR-Operates b Contact Of the Assigned Contact And The Connected Contact In Parallel, And Takes The Result As Operation Result.
ORP	ORP (S)	If Input Condition Of Connection In Parallel Contact Is OFF From ON, Sets For One Scan.
ORF	ORF (S)	If Input Condition Of Connection In Parallel Contact Is OFF From ON, Sets For One Scan.
INV	INV	Inverts The Left Circuit, A Contact Circuit To B Contact Circuit And B Contact Circuit To A Contact Circuit.

Connection

Instruction	Type of Input	Note
ANB	ANB	AND-Operates Blocks And Takes The Result As Operation Result.
ORB	ORB	OR-Operates Blocks And Takes The result As Operation Result.
MPS	MPS	It IS Used To Branch At First. Stores Operation Result In Memory.
MRD	MRD	It Is Used To Relay Branching. Reads The Stored State From Memory And Operates The Result.
MPP	MPP	It Is Used to End Branching. Reads The Stored State From Memory And Operates The Result.

Output

Instruction	Type of Input	Note
OUT	OUT (D)	Outputs Operation Result To The Assigned Contact.
SET	SET (D)	If Input Condition Is ON, Keeps Output Contact In ON State. Though The Input Is OFF, Keeps Setting Output.
PLS	PLS (D)	If INput Condition IS ON From OFF, Sets The Assigned Contact For One Scan. Otherwise, Resets.
PLF	PLF (D)	If Input Condition Is OFF From ON, Sets The Assigned Contact For One Scan. Otherwise, Resets.

Master Control

Instruction	Type of Input	Note
MC	MC (n)	If Input Of MC Is ON, Operates Up To Same MCR. If Input Conditon Is OFF, Does Not Operates.
MCR	MCR (n)	If Input Of MC Is ON, Operates Up To Same MCR. If Input Conditon Is OFF, Does Not Operates.

Jump

Instruction	Type of Input	Note
JME	JME (n)	If Input Of JMP n Instruction Is On, Jumps Next To JME n And Does Not Process All The Instructions Up To JME n.
JMP	JMP (n)	If Input Of JMP n Instruction Is On, Jumps Next To JME n And Does Not Process All The Instructions Up To JME n.
JMPP	JMPP (n)	If JMPP n Instruction Input Is On, Jumps Next To JME n And Does Not Process All The Instructions Up To JME n.

Call

Instruction	Type of Input	Note
CALL	CALL (n)	If Input Condition Is ON While Processing Program, Processes The Program Between The SBRT n To The RET According To The CALL n.
CALLP	CALLP (n)	If Input Condition Is ON While Processing Program, Processes The Program Between The SBRT n To The RET According To The CALL n.
ECALL	ECALL (Progam ID) (n)	Calls Sub-Routine From Other Program File. (Pn-Point Number Of Sub-Routine)
ECALLP	ECALLP (Program ID) (n)	Calls Sub-Routine From Other Program File. (Pn-Point Number Of Sub-Routine)
SBRT	SBRT (n)	If Input Condition Is ON While Running Program, Runs The Program Between SBRT n And RET Accoding To CALL n.
RET	RET	If Input Condition Is ON While Running Program, Runs The Program Between SBRT n And RET Accoding To CALL n.

Interrupt

Instruction	Type of Input	Note
EI	EI (n)	Operates Time Driven Interrrupt Assigned To n.
DI	DI (n)	Stops Operating Time Driven Interrupt Assigned To n.
GEI	GEI	Operates Time Driven Interrrupt In Entire Program.
GDI	GDI	Stops Operating Time Driven Interrrupt In Entire Program.
IRET	IRET	Shows THe End OF Interrupt Program.

Loop

Instruction	Type of Input	Note
FOR	FOR (n)	Runs The Step Next To NEXT Instruction After Has Processed Between FOR And NEXT At n Times.
NEXT	NEXT	Runs The Step Next To NEXT Instruction After Has Processed Between FOR And NEXT At n Times.
BREAK	BREAK	Comes Out From The FOR ~ NEXT Instruction.
BREAKP	BREAKP	Comes Out From The FOR ~ NEXT Instruction.

END

Instruction	Type of Input	Note
END	END	It Is The Instruction To Inform Ending Main Routine Program. In Case Jump Instruction Prior To It Is Operated, It Is Not Operated.
CEND	CEND	If input condition is turned on, ends main routine program.
CENDP	CENDP	If input condition is turned on, ends main routine program.
PEND	PEND	It Means End Of Program And Is Put On The Last Part.
STOP	STOP	To Stop Operation At The Time When Users Want, Converts To Program Mode After Finishing The Scan In Progress.
INITEND	INITEND	Ends Initialization Program ANd Runs Scan Program.

Compare

Instruction	Type of Input	Note
LD<	LD< (S1) (S2)	If Data In S1 Is Less Than Data In S2, Sets Result Of The Current Operation.
LD<=	LD<= (S1) (S2)	If Data In S1 Is Less Than Or Equal To Data In S2, Sets Result Of The Current Operation.
LD<>	LD<> (S1) (S2)	If Data In S1 Is Not Equal To Data In S2, Sets Result Of The Current Operation.
LD=	LD= (S1) (S2)	If Data In S1 Is Equal To Data In S2, Sets Result Of The Current Operation.
LD>	LD> (S1) (S2)	If Data In S1 Is Greater Than Data In S2, Sets Result Of The Current Operation.
LD>=	LD>= (S1) (S2)	If Data In S1 Is Greater Than Or Equal To Data In S2, Sets Result Of The Current Operation.
AND<	AND< (S1) (S2)	If Data S1 Is Less Than Data S2, ON. If Greater Than Or Equal To, OFF. AND-Operates The Result And Result Of The Current Operation.
AND<=	AND<= (S1) (S2)	If Data S1 Is Less Than Or Equal To Data S2, ON. If Greater Than, OFF. AND-Operates The Result And Result Of The Current Operation.
AND<>	AND<> (S1) (S2)	If Data S1 And Data S2 Are Not Equal, ON. If Equal, OFF. AND-Operates The Result And Result Of The Current Operation.
AND=	AND= (S1) (S2)	If Data S1 And Data S2 Are Equal, ON. If TNot Equal, OFF. AND-Operates The Result And Result Of The Current Operation.
AND>	AND> (S1) (S2)	If Data S1 Is Greater Than Data S2, ON. If Less Than Or Equal To, OFF. AND-Operates The Result And Result Of The Current Operation.
AND>=	AND>= (S1) (S2)	If Data S1 Is Greater Than Or Equal To Data S2, ON. If Less Than, OFF. AND-Operates The Result And Result Of The Current Operation.
OR<	OR< (S1) (S2)	If Data In S1 Is Less Than Data In S2, Sets.If Greater Than Or Equal To, Resets. OR-Operates The Result And Result Of The Current Operation.
OR<=	OR<= (S1) (S2)	If Data In S1 Is Less Than Or Equal To Data In S2, Sets. If Greater Than, Resets. OR-Operates The Result And Result Of The Current Operation.
OR<>	OR<> (S1) (S2)	If Data In S1 Is Not Equal To Data In S2, Sets. If Equal To, Off. OR-Operates The Result And Result Of The Current Operation.
OR=	OR= (S1) (S2)	If Data In S1 Is Equal To Data In S2, Sets. If Not Equal To, Resets. OR-Operates The Result And Result Of The Current Operation.
OR>	OR> (S1) (S2)	If Data In S1 Is Greater than Data In S2, Sets. If Less than Or Equal To, Resets. OR-Operates The Result And Result Of The Current Operation.
OR>=	OR>= (S1) (S2)	If Data InS1 Is Greater Than Or Equal To Data In S2, Sets. If Less Than, Resets. OR-Operates The Result And Result Of The Current Operation.
UCMP	UCMP (S1) (S2)

Compare (DWORD)

Instruction	Type of Input	Note
LDD<	LDD< (S1) (S2)	If Data In S1 Is Less Than Data In S2, Sets Result Of The Current Operation.
LDD<=	LDD<= (S1) (S2)	If Data In S1 Is Less Than Or Equal To Data In S2, Sets Result Of The Current Operation.
LDD<>	LDD<> (S1) (S2)	If Data In S1 Is Not Equal To Data In S2, Sets Result Of The Current Operation.
LDD=	LDD= (S1) (S2)	If Data In S1 Is Equal To Data In S2, Sets Result Of The Current Operation.
LDD>	LDD> (S1) (S2)	If Data In S1 Is Greater Than Data In S2, Sets Result Of The Current Operation.
LDD>=	LDD>= (S1) (S2)	If Data In S1 Is Greater Than Or Equal To Data In S2, Sets Result Of The Current Operation.
ANDD<	ANDD< (S1) (S2)	If Double-Word Data S1 Is Less Than Double-Word Data S2, ON. If Greater Than Or Equal To, OFF. AND-Operates The Result And Result Of The Current Operation.
ANDD<=	ANDD<= (S1) (S2)	ANDD<= (S1) (S2)" , "If Double-Word Data S1 Is Less Than Or Equal To Double-Word Data S2, On. If Greater Than, OFF. AND-Operates The Result And Result Of The Current Operation.
ANDD<>	ANDD<> (S1) (S2)	ANDD<> (S1) (S2)" , "If Double-Word Data S1 Is Not Equal To Double-Word Data S2, ON. If Equal To, OFF. AND-Operates The Result And Result Of The Current Operation.
ANDD=	ANDD= (S1) (S2)	ANDD= (S1) (S2)" , "If Double-Word Data S1 Is Equal To Double- Word Data S2, ON. If Not Equal to, OFF.AND-Operates The Result And Result Of The Current Operation.
ANDD>	ANDD> (S1) (S2)	ANDD> (S1) (S2)" , "If Double-Word Data S1 Is Greater Than Double-Word Data S2, ON. If Less Than, OFF. AND-Operates The Result And Result Of The Current Operation.
ANDD>=	ANDD>= (S1) (S2)	ANDD>= (S1) (S2)" , "If Double-Word Data S1 Is Greater Than Or Equal To Double-Word Data S2, ON. If Less Than, OFF. AND-Operates The Result And Result Of The Current Operation.
ORD<	ORD< (S1) (S2)	If Data In S1 Is Less Than Data In S2, Sets. If Greater Than Or Equal To, Off. OR-Operates The Result And Result Of The Current Operation.
ORD<=	ORD<= (S1) (S2)	If Data In S1 Is Less Than Or Equal To Data In S2, Sets. If Greater Than, Resets. OR-Operates The Result And Result Of The Current Operation.
ORD<>	ORD<> (S1) (S2)	If Data In S1 Is Not Equal To Data In S2, Sets. If Equal To, resets. OR-Operates The Result And Result Of The Current Operation.
ORD=	ORD= (S1) (S2)	If Data In S1 Is Equal To Data In S2, Sets. If Not Equal To, Resets. OR-Operates The Result And Result Of The Current Operation.
ORD>	ORD> (S1) (S2)	If Data In S1 Is Greater Than Data In S2, Sets. If Less Than Or Equal To, Resets. OR-Operates The Result And Result Of The Current Operation.
ORD>=	ORD>= (S1) (S2)	If Data In S1 Is Greater Than Or Equal To Data In S2, Sets. If Less Than, Resets. OR-Operates The Result And Result Of The Current Operation.

Compare (Block)

Instruction	Type of Input	Note
BK=	BK= (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK=P	BK=P (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK<>	BK<> (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK<>P	BK<>P (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK<	BK< (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK<P	BK<P (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK<=	BK<= (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK<=P	BK<=P (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK>	BK> (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK>P	BK>P (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK>=	BK>= (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].
BK>=P	BK>=P (S1) (S2) (D) (B) (n)	Compare [n] of 16 bit data from the device designated by [S1] with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D]. Compare 16 bit data with [n] of 16 bit data from the device designated by [S2] and stores the results from bit [n] of the device designated by [D].

Compare (Floating decimal point)

Instruction	Type of Input	Note
LDE<	LDD< (S1) (S2)	If Float Data In S1 Is Less Than Float Data In S2, Sets Result Of The Current Operation.
LDE<=	LDD<= (S1) (S2)	If Float Data In S1 Is Less Than Or Equal To Float Data In S2, Sets Result Of The Current Operation.
LDE<>	LDD<> (S1) (S2)	If Float Data In S1 Is Not Equal To Float Data In S2, Sets Result Of The Current Operation.
LDE=	LDD= (S1) (S2)	If Float Data In S1 Is Equal To Float Data In S2, Sets Result Of The Current Operation.
LDE>	LDD> (S1) (S2)	If Float Data In S1 Is Greater Than Float Data In S2, Sets Result Of The Current Operation.
LDE>=	LDD>= (S1) (S2)	If Float Data In S1 Is Greater Than Or Equal To Float Data In S2, Sets Result Of The Current Operation.
ANDE<	ANDD< (S1) (S2)	If Float Data In S1 Is Less Than Float Data In S2, Sets Result Of The Current Operation.
ANDE<=	ANDD<= (S1) (S2)	If Float Data In S1 Is Less Than Or Equal To Float Data In S2, Sets Result Of The Current Operation.
ANDE<>	ANDD<> (S1) (S2)	If Float Data In S1 Is Not Equal To Float Data In S2, Sets Result Of The Current Operation.
ANDE=	ANDD= (S1) (S2)	If Float Data In S1 Is Equal To Float Data In S2, Sets Result Of The Current Operation.
ANDE>	ANDD> (S1) (S2)	If Float Data In S1 Is Greater Than Float Data In S2, Sets Result Of The Current Operation.
ANDE>=	ANDD>= (S1) (S2)	If Float Data In S1 Is Greater Than Or Equal To Float Data In S2, Sets Result Of The Current Operation.
ORE<	ORD< (S1) (S2)	If Float Data In S1 Is Less Than Float Data In S2, Sets Result Of The Current Operation.
ORE<=	ORD<= (S1) (S2)	f Float Data In S1 Is Less Than Or Equal To Float Data In S2, Sets Result Of The Current Operation.
ORE<>	ORD<> (S1) (S2)	If Float Data In S1 Is Not Equal To Float Data In S2, Sets Result Of The Current Operation.
ORE=	ORD= (S1) (S2)	If Float Data In S1 Is Equal To Float Data In S2, Sets Result Of The Current Operation.
ORE>	ORD> (S1) (S2)	If Float Data In S1 Is Greater Than Float Data In S2, Sets Result Of The Current Operation.
ORE>=	ORD>= (S1) (S2)	If Float Data In S1 Is Greater Than Or Equal To Float Data In S2, Sets Result Of The Current Operation.

Arithmetic

Instruction	Type of Input	Note
ADD	ADD (S1) (S2) (D)	Adds Data S1 To Data S2, And Stores The Result In Device D.
ADDP	ADDP (S1) (S2) (D)	Adds Data S1 To Data S2, And Stores The Result In Device D.
SUB	SUB (S1) (S2) (D)	Subtracts Data In S2 From Data In S1 And Stores The Result In Device D.
SUBP	SUBP (S1) (S2) (D)	Subtracts Data In S2 From Data In S1 And Stores The Result In Device D.
MUL	MUL (S1) (S2) (D)	Multiplies Data In S1 By Data In S2 And Stores The Result In D.
MULP	MULP (S1) (S2) (D)	Multiplies Data In S1 By Data In S2 And Stores The Result In D.
DIV	DIV (S1) (S2) (D)	Divides Data In S1 By Data In S2 And Stores The Resutl In Device D.
DIVP	DIVP (S1) (S2) (D)	Divides Data In S1 By Data In S2 And Stores The Resutl In Device D.
WMUL	WMUL (S1) (S2) (D)	Multiplies BIN 32-bit data designated by S1, S1+1 and BIN 32-bit data designated by S2, S2+1 and stores the result in the device designated by D, D+1.
WMULP	WMULP (S1) (S2) (D)	Multiplies BIN 32-bit data designated by S1, S1+1 and BIN 32-bit data designated by S2, S2+1 and stores the result in the device designated by D, D+1.
WDIV	WDIV (S1) (S2) (D)	This is used to divide the double data in the device assigned to S1, S1+1 by the DOUBLE data in the device assigned to S2, S2+1 storing the quotient of the result in the device assigned to D
WDIVP	WDIVP (S1) (S2) (D)	This is used to divide the double data in the device assigned to S1, S1+1 by the DOUBLE data in the device assigned to S2, S2+1 storing the quotient of the result in the device assigned to D
WSUM	WSUM (S) (D) (n)	Summed up all 16bit binary data for n words from the device designated at S, and stored it in the device designated at D
WSUMP	WSUMP (S) (D) (n)	Summed up all 16bit binary data for n words from the device designated at S, and stored it in the device designated at D

Arithmetic (DWORD)

Instruction	Type of Input	Note
DADD	DADD (S1) (S2) (D)	Adds Double- Word Data In S2 To Double-Word Data In S1 And Stores The Result In Device D.
DADDP	DADDP (S1) (S2) (D)	Adds Double- Word Data In S2 To Double-Word Data In S1 And Stores The Result In Device D.
DSUB	DSUB (S1) (S2) (D)	Subtract Double- Word Data In S2 From Double-Word Data In S1 And Stores The result In D.
DSUBP	DSUBP (S1) (S2) (D)	Subtract Double- Word Data In S2 From Double-Word Data In S1 And Stores The result In D.
DMUL	DMUL (S1) (S2) (D)	Multiplies Double-Word Data In S1 By Double-Word Data In S2 And Stores The Result In D.
DMULP	DMULP (S1) (S2) (D)	Multiplies Double-Word Data In S1 By Double-Word Data In S2 And Stores The Result In D.
DDIV	DDIV (S1) (S2) (D)	Divides Double-Word Data In S1 By Double-Word Data In S2 And Stores The Result In Device D.
DDIVP	DDIVP (S1) (S2) (D)	Divides Double-Word Data In S1 By Double-Word Data In S2 And Stores The Result In Device D.
DWMUL	WMUL (S1) (S2) (D)	Multiplies BIN 32-bit data designated by S1, S1+1 and BIN 32-bit data designated by S2, S2+1 and stores the result in the device designated by D, D+1.
DWMULP	WMULP (S1) (S2) (D)	Multiplies BIN 32-bit data designated by S1, S1+1 and BIN 32-bit data designated by S2, S2+1 and stores the result in the device designated by D, D+1.
DWDIV	WDIV (S1) (S2) (D)	This is used to divide the double data in the device assigned to S1, S1+1 by the DOUBLE data in the device assigned to S2, S2+1 storing the quotient of the result in the device assigned to D
DWDIVP	WDIVP (S1) (S2) (D)	This is used to divide the double data in the device assigned to S1, S1+1 by the DOUBLE data in the device assigned to S2, S2+1 storing the quotient of the result in the device assigned to D

Arithmetic (BCD)

Instruction	Type of Input	Note
BADD	BADD (S1) (S2) (D)	Adds 4 Digits BCD Data In S1 To 4 Digits BCD Data In S2, And Stores The Result In Device D.
BADDP	BADDP (S1) (S2) (D)	Adds 4 Digits BCD Data In S1 To 4 Digits BCD Data In S2, And Stores The Result In Device D.
BSUB	BSUB (S1) (S2) (D)	Subtracts 4 Digits BCD Data In S2 From 4 Digits BCD Data In S1 And Stores The Result In Device D.
BSUBP	BSUBP (S1) (S2) (D)	Subtracts 4 Digits BCD Data In S2 From 4 Digits BCD Data In S1 And Stores The Result In Device D.
BMUL	BMUL (S1) (S2) (D)	Mutiplies 4 Digits BCD Data In S1 By 4 Digits BCD Data In S2.
BMULP	BMULP (S1) (S2) (D)	Mutiplies 4 Digits BCD Data In S1 By 4 Digits BCD Data In S2.
BDIV	BDIV (S1) (S2) (D)	Divides 4 Digits BCD Data In S1 By 4 Digits BCD Data In S2 And Stores The Result In Device D.
BDIVP	BDIVP (S1) (S2) (D)	Divides 4 Digits BCD Data In S1 By 4 Digits BCD Data In S2 And Stores The Result In Device D.

Arithmetic (BCD, DWORD)

Instruction	Type of Input	Note
DBADD	DBADD (S1) (S2) (D)	Adds 4 Digits BCD Double-Word Data In S2 To 4 Digits BCD Double-Word Data In S1 And Stores The Result In Device D.
DBADDP	DBADDP (S1) (S2) (D)	Adds 4 Digits BCD Double-Word Data In S2 To 4 Digits BCD Double-Word Data In S1 And Stores The Result In Device D.
DBSUB	DBSUB (S1) (S2) (D)	Subtracts 8 Digits BCD Data In S2 From 8 Digits BCD Data In S1.
DBSUBP	DBSUBP (S1) (S2) (D)	Subtracts 8 Digits BCD Data In S2 From 8 Digits BCD Data In S1.
DBMUL	DBMUL (S1) (S2) (D)	Multiplies 8 Digits BCD Data In S1 By 8 Digits BCD Data In S2.
DBMULP	DBMULP (S1) (S2) (D)	Multiplies 8 Digits BCD Data In S1 By 8 Digits BCD Data In S2.
DBDIV	DBDIV (S1) (S2) (D)	Divides 8 Digits BCD Data In S1 By 8 Digits BCD Data And Stores The Result In Device D.
DBDIVP	DBDIVP (S1) (S2) (D)	Divides 8 Digits BCD Data In S1 By 8 Digits BCD Data And Stores The Result In Device D.

Arithmetic (Floating decimal point, XP)

Instruction	Type of Input	Note
EADD	EADD (S1) (S2) (D)	This is used to add the floating-point data in the device assigned to S1 to the floating-point data in the device assigned to S2, storing the result in the device assigned D.
EADDP	EADDP (S1) (S2) (D)	This is used to add the floating-point data in the device assigned to S1 to the floating-point data in the device assigned to S2, storing the result in the device assigned D.
ESUB	ESUB (S1) (S2) (D)	This is used to subtract the Floating-point data in the device assigned to S2 from the Floating-point data in the device assigned to S1, storing the result in the device assigned to D.
ESUBP	ESUBP (S1) (S2) (D)	This is used to subtract the Floating-point data in the device assigned to S2 from the Floating-point data in the device assigned to S1, storing the result in the device assigned to D.
EMUL	EMUL (S1) (S2) (D)	This is used to multiply the Floating-point data assigned to S1 by the Floating-point data in the device assigned to S2, storing the result in the device assigned to D.
EMULP	EMULP (S1) (S2) (D)	This is used to multiply the Floating-point data assigned to S1 by the Floating-point data in the device assigned to S2, storing the result in the device assigned to D.
EDIV	EDIV (S1) (S2) (D)	This is used to divide the floating-point data in the device assigned to S1 to the floating-point data in the device assigned to S2, storing the result in the device assigned D.
EDIVP	EDIVP (S1) (S2) (D)	This is used to divide the floating-point data in the device assigned to S1 to the floating-point data in the device assigned to S2, storing the result in the device assigned D.

INC / DEC

Instruction	Type of Input	Note
INC	INC (D)	Adds 1 To Data Value In D And Stores The Result In D Again.
INCP	INCP (D)	Adds 1 To Data Value In D And Stores The Result In D Again.
DINC	DINC (D)	Adds 1 To Double-Word Data Value In D And Stores The Result In D Again.
DINCP	DINCP (D)	Adds 1 To Double-Word Data Value In D And Stores The Result In D Again.
DEC	DEC (D)	Subtracts 1 From Data Value In D And Stores The Result In Device D Again.
DECP	DECP (D)	Subtracts 1 From Data Value In D And Stores The Result In Device D Again.
DDEC	DDEC (D)	Subtracts 1 From Double-Word Data Value In D And Stores The Result In Device D Again.
DDECP	DDECP (D)	Subtracts 1 From Double-Word Data Value In D And Stores The Result In Device D Again.

Complement

Instruction	Type of Input	Note
NEG	NEG (D)	Sign-Inverts Contents Of Data In D And Stores The Result In D Again.
NEGP	NEGP (D)	Sign-Inverts Contents Of Data In D And Stores The Result In D Again.
DNEG	DNEG (D)	Sign-Inverts Contents Of Double-Word Data In D And Stores The Result In D Again.
DNEGP	DNEGP (D)	Sign-Inverts Contents Of Double-Word Data In D And Stores The Result In D Again.

MIN / MAX

Instruction	Type of Input	Note
MAX	MAX (S) (D) (n)	Stores The Biggest Value Among n Pieces Of Data From Data In S, Its Location And Number Of The Values In D.
MAXP	MAXP (S) (D) (n)	Stores The Biggest Value Among n Pieces Of Data From Data In S, Its Location And Number Of The Values In D.
MIN	MIN (S) (D) (n)	Stores The Smallest Value Among n Pieces Of Data From Data In S, Its Location And Number Of The Values In D.
MINP	MINP (S) (D) (n)	Stores The Smallest Value Among n Pieces Of Data From Data In S, Its Location And Number Of The Values In D.
DMAX	DMAX (S) (D) (n)	Stores The Biggest Value Among n Pieces Of Data From Double-Word Data Of S, Its Location And Number Of The Values In D.
DMAXP	DMAXP (S) (D) (n)	Stores The Biggest Value Among n Pieces Of Data From Double-Word Data Of S, Its Location And Number Of The Values In D.
DMIN	DMIN (S) (D) (n)	Stores The Smallest Value Among n Pieces Of Data From Double-Word Data Of S, Its Location And Number Of The Values In D.
DMINP	DMINP (S) (D) (n)	Stores The Smallest Value Among n Pieces Of Data From Double-Word Data Of S, Its Location And Number Of The Values In D.

Transmit Data

Instruction	Type of Input	Note
MOV	MOV (S) (D)	Transmits Word Data In Device S To Device D.
MOVP	MOVP (S) (D)	Transmits Word Data In Device S To Device D.
DMOV	DMOV (S) (D)	Transmits Double-Word Data In Device S To Device D.
DMOVP	DMOVP (S) (D)	Transmits Double-Word Data In Device S To Device D.
CML	CML (S) (D)	Inverts Each Bit Of Data In Device S And Stores The Result In Device D.
CMLP	CMLP (S) (D)	Inverts Each Bit Of Data In Device S And Stores The Result In Device D.
DCML	DCML (S) (D)	Inverts Each Bit Of Double-Word Data In S And Stores The Result In Device D.
DCMLP	DCMLP (S) (D)	Inverts Each Bit Of Double-Word Data In S And Stores The Result In Device D.
BMOV	BMOV (S) (D) (n)	Transmits n Pieces Of Data In S To Device D.
BMOVP	BMOVP (S) (D) (n)	Transmits n Pieces Of Data In S To Device D.
FMOV	FMOV (S) (D) (n)	Transmits Data In S To n Pieces Of Device From Device D In Due Order.
FMOVP	FMOVP (S) (D) (n)	Transmits Data In S To n Pieces Of Device From Device D In Due Order.
WBMOV	WBMOV (S) (D) (fm)	transfer bit data from S to D, obey fm
WBMOVP	WBMOVP (S) (D) (fm)	transfer bit data from S to D, obey fm

Exchange Data

Instruction	Type of Input	Note
XCH	XCH (D1) (D2)	Exchanges Word Data In S With Word Data In D.
XCHP	XCHP (D1) (D2)	Exchanges Word Data In S With Word Data In D.
DXCH	DXCH (S) (D)	Exchanges Double-Word Data In S With Double-Word Data In D Each Other.
DXCHP	DXCHP (S) (D)	Exchanges Double-Word Data In S With Double-Word Data In D Each Other.
BXCH	BXCH (D1) (D2) (n)	Exchanges n Pieces Of Data In Device S And n Pieces Of Data In Device D Each Other.
BXCHP	BXCHP (D1) (D2) (n)	Exchanges n Pieces Of Data In Device S And n Pieces Of Data In Device D Each Other.
SWAP	SWAP (D)	Exchanges The Upper Byte Of Data In D With The Lower Byte Of It And Stores The Result In Device D.
SWAPP	SWAPP (D)	Exchanges The Upper Byte Of Data In D With The Lower Byte Of It And Stores The Result In Device D.

Logical

Instruction	Type of Input	Note
WAND	WAND (S1) (S2) (D)	AND-Operates Data In S1 And Data In S2, And Stores In Device D.
WANDP	WANDP (S1) (S2) (D)	AND-Operates Data In S1 And Data In S2, And Stores In Device D.
WOR	WOR (S1) (S2) (D)	OR-Operates Data In S1 And Data In S2, And Stores The Result In Device D.
WORP	WORP (S1) (S2) (D)	OR-Operates Data In S1 And Data In S2, And Stores The Result In Device D.
WXOR	WXOR (S1) (S2) (D)	Exclusive - OR-Operates Data In S1 And Data In S2, And Stores The Result In D.
WXORP	WXORP (S1) (S2) (D)	Exclusive - OR-Operates Data In S1 And Data In S2, And Stores The Result In D.
WXNR	WXNR (S1) (S2) (D)	Exclusive - NOR-Operates Data In S1 And Data In S2, And Stores The Result In D.
WXNRP	WXNRP (S1) (S2) (D)	Exclusive - NOR-Operates Data In S1 And Data In S2, And Stores The Result In D.

Logical (DWORD)

Instruction	Type of Input	Note
DAND	DAND (S1) (S2) (D)	AND-Operates Data In Device S1 And Data In Device S2, And Stores The Result In Device D.
DANDP	DANDP (S1) (S2) (D)	AND-Operates Data In Device S1 And Data In Device S2, And Stores The Result In Device D.
DOR	DOR (S1) (S2) (D)	OR-Operates Data In S1 And 32 Bit Data In S2, And Stores The Result In D.
DORP	DORP (S1) (S2) (D)	OR-Operates Data In S1 And 32 Bit Data In S2, And Stores The Result In D.
DXOR	DXOR (S1) (S2) (D)	Exclusive - OR-Operates Double-Word Data In S1 And Double-Word Data In S2, And Stores The Result In D.
DXORP	DXORP (S1) (S2) (D)	Exclusive - OR-Operates Double-Word Data In S1 And Double-Word Data In S2, And Stores The Result In D.
DXNR	DXNR (S1) (S2) (D)	Exclusive - NOR-Operates Double-Word Data In S1 And Double-Word Data In S2, And Stores The Result In D.
DXNRP	DXNRP (S1) (S2) (D)	Exclusive - NOR-Operates Double-Word Data In S1 And Double-Word Data In S2, And Stores The Result In D.

Logical (Block)

Instruction	Type of Input	Note
BKAND	BKAND (S1) (S2) (D) (n)	AND-Operates n Pieces Of Data In Device S1 And n Pieces OF Data In Device S2, And Stores The Result In Device D.
BKANDP	BKANDP (S1) (S2) (D) (n)	AND-Operates n Pieces Of Data In Device S1 And n Pieces OF Data In Device S2, And Stores The Result In Device D.
BKOR	BKOR (S1) (S2) (D) (n)	OR-Operates n Pieces Of Data In S1 And n Pieces Of Data In S2, And Stores The Result In Device D.
BKORP	BKORP (S1) (S2) (D) (n)	OR-Operates n Pieces Of Data In S1 And n Pieces Of Data In S2, And Stores The Result In Device D.
BKXOR	BKXOR (S1) (S2) (D) (n)	Exclusive - OR-Operates n Pieces Of Data In S1 And n Pieces Of Data In S2, And Stores The Result In Device D.
BKXORP	BKXORP (S1) (S2) (D) (n)	Exclusive - OR-Operates n Pieces Of Data In S1 And n Pieces Of Data In S2, And Stores The Result In Device D.
BKXNR	BKXNR (S1) (S2) (D) (n)	Exclusive - NOR-Operates n Pieces Of Data In S1 And n Pieces Of Data In S2, And Stores The Result In Device D.
BKXNRP	BKXNRP (S1) (S2) (D) (n)	Exclusive - NOR-Operates n Pieces Of Data In S1 And n Pieces Of Data In S2, And Stores The Result In Device D.

Rotation

Instruction	Type of Input	Note
ROL	ROL (D) (n)	Shifts Left 16 Pieces Of Bit In D As Much As n Bits. Shifts The Uppermost Bit To The Lowest Bit And Carry Flag.
ROLP	ROLP (D) (n)	Shifts Left 16 Pieces Of Bit In D As Much As n Bits. Shifts The Uppermost Bit To The Lowest Bit And Carry Flag.
ROR	ROR (D) (n)	Shifts Right 16 Pieces Of Bit In D As Much As n Bits. Shifts The Lowest Bit To Carry Flag And Carry Flag To The Uppermost Bit.
RORP	RORP (D) (n)	Shifts Right 16 Pieces Of Bit In D As Much As n Bits. Shifts The Lowest Bit To Carry Flag And Carry Flag To The Uppermost Bit.

Rotation (Carry)

Instruction	Type of Input	Note
RCL	RCL (D) (n)	Shifts Left 16 Pieces Of Bit In D As Much As n Bits. Shifts The Uppermost Bit To Carry Flag And Carry Flag To The Lowest Bit.
RCLP	RCLP (D) (n)	Shifts Left 16 Pieces Of Bit In D As Much As n Bits. Shifts The Uppermost Bit To Carry Flag And Carry Flag To The Lowest Bit.
RCR	RCR (D) (n)	Shifts Right 16 Pieces Of Bit In D As Much As n Bits. Shifts The Lowest Bit To Carry Flag And Carry Flag.
RCRP	RCRP (D) (n)	Shifts Right 16 Pieces Of Bit In D As Much As n Bits. Shifts The Lowest Bit To Carry Flag And Carry Flag.

Rotation (DWORD)

Instruction	Type of Input	Note
DROL	DROL (D) (n)	Shifts Left 32 Bits In D As Much As n Bits. Shifts The Uppermost Bit To The Lowest Bit And Carry Flag.
DROLP	DROLP (D) (n)	Shifts Left 32 Bits In D As Much As n Bits. Shifts The Uppermost Bit To The Lowest Bit And Carry Flag.
DROR	DROR (D) (n)	Shifts Right 32 Bits In D As Much As n Bits. Shifts The Lowest Bit To Carry Flag And Carry Flag To The Uppermost Bit.
DRORP	DRORP (D) (n)	Shifts Right 32 Bits In D As Much As n Bits. Shifts The Lowest Bit To Carry Flag And Carry Flag To The Uppermost Bit.

Rotation (DWORD, Carry)

Instruction	Type of Input	Note
DRCL	DRCL (D) (n)	Shifts Left 32 Bits In D As Much As n Bits. Shifts The Uppermost Bit To Carry Flag And Carry Flag To The Lowest Bit.
DRCLP	DRCLP (D) (n)	Shifts Left 32 Bits In D As Much As n Bits. Shifts The Uppermost Bit To Carry Flag And Carry Flag To The Lowest Bit.
DRCR	DRCR (D) (n)	Shifts Right 32 Bits In D As Much As n Bits. Shifts The Lowest Bit To The Uppermost Bit And Carry Flag.
DRCRP	DRCRP (D) (n)	Shifts Right 32 Bits In D As Much As n Bits. Shifts The Lowest Bit To The Uppermost Bit And Carry Flag.

Shift

Instruction	Type of Input	Note
SFL	SFL (D) (n)	Shifts Left Data Bit In D As Much As n Bits. Fills Lower n Bits With 0 And Stores the Result In D.
SFLP	SFLP (D) (n)	Shifts Left Data Bit In D As Much As n Bits. Fills Lower n Bits With 0 And Stores the Result In D.
SFR	SFR (D) (n)	Shifts Right Data Bit In D As Much As n Bits. Fills Upperr n Bits With 0 And Stores the Result In D.
SFRP	SFRP (D) (n)	Shifts Right Data Bit In D As Much As n Bits. Fills Upperr n Bits With 0 And Stores the Result In D.

Shift (BIT)

Instruction	Type of Input	Note
BSFL	BSFL (D) (n)	n Pieces Of Data Are Shifted Left From Data In Device D And The Shifted Lowest Data Is Filled With 0.
BSFLP	BSFLP (D) (n)	n Pieces Of Data Are Shifted Left From Data In Device D And The Shifted Lowest Data Is Filled With 0.
BSFR	BSFR (D) (n)	n Pieces Of Data Are Shifted Right From Data In Device D And The Shifted Uppermost Data Is Filled With 0.
BSFRP	BSFRP (D) (n)	n Pieces Of Data Are Shifted Right From Data In Device D And The Shifted Uppermost Data Is Filled With 0.

Shift (WORD)

Instruction	Type of Input	Note
DSFL	DSFL (D) (n)	Shifts Left Double-Word Data Bits In D As Much As n Bits. Fills Lower n Bits With 0 And Stores Them In D.
DSFLP	DSFLP (D) (n)	Shifts Left Double-Word Data Bits In D As Much As n Bits. Fills Lower n Bits With 0 And Stores Them In D.
DSFR	DSFR (D) (n)	Shifts Right Double-Word Data Bits In D As Much As n Bits. Fills Upper n Bits With 0 And Stores Them In D.
DSFRP	DSFRP (D) (n)	Shifts Right Double-Word Data Bits In D As Much As n Bits. Fills Upper n Bits With 0 And Stores Them In D.

Conversion (BIN -> BCD)

Instruction	Type of Input	Note
BCD	BCD (S) (D)	Converts BIN Data Value In S To BCD Data And Stores The Result In Device D.
BCDP	BCDP (S) (D)	Converts BIN Data Value In S To BCD Data And Stores The Result In Device D.
DBCD	DBCD (S) (D)	Converts BIN DOuble-Word Data Value In S To BCD Double-Word Data And Stores The Result In Device D.
DBCDP	DBCDP (S) (D)	Converts Double-Word BIN Data Value In S To BCD Data And Stores The result In Device D.

Conversion (BCD -> BIN)

Instruction	Type of Input	Note
BIN	BIN (S) (D)	Converts 4 Digits BCD Data Value In S To BIN Data And Stores The Result In Device D.
BINP	BINP (S) (D)	Converts 4 Digits BCD Data Value In S To BIN Data And Stores The Result In Device D.
DBIN	DBIN (S) (D)	Converts 8 Digits BCD Data Value In S To BIN Data And Stores The Result In Device D.
DBINP	DBINP (S) (D)	Converts 8 Digits BCD Data Value In S To BIN Data And Stores The Result In Device D.

Conversion (BIN -> ASCII)

Instruction	Type of Input	Note
BINDA	BINDA (S) (D)	Converts BIN Data In S To Decimal ASCII Code And Stores The Result In Device D.
BINDAP	BINDAP (S) (D)	Converts BIN Data In S To Decimal ASCII Code And Stores The Result In Device D.
DBINDA	DBINDA (S) (D)	Converts BIN Data In S To Decimal ASCII Code And Stores The Result In Device D.
DBINDAP	DBINDAP (S) (D)	Converts BIN Data In S To Decimal ASCII Code And Stores The Result In Device D.

Conversion (ASCII -> BIN)

Instruction	Type of Input	Note
DABIN	DABIN (S) (D)	Converts Decimal ASCII Code In Device S To 16bit BIN Data And Stores The Result In Device D.
DABINP	DABINP (S) (D)	Converts Decimal ASCII Code In Device S To 16bit BIN Data And Stores The Result In Device D.
DDABIN	DDABIN (S) (D)	Converts Decimal ASCII Code In S To 32 Bit BIN Data And Stores The Result In Device D.
DDABINP	DDABINP (S) (D)	Converts Decimal ASCII Code In S To 32 Bit BIN Data And Stores The Result In Device D.

Conversion ( BIN -> HEX ASCII)

Instruction	Type of Input	Note
BINHA	BINHA (S) (D)	Converts BIN Data In S To Hexadecimal ASCII Code And Stores The Result In Device D.
BINHAP	BINHAP (S) (D)	Converts BIN Data In S To Hexadecimal ASCII Code And Stores The Result In Device D.
DBINHA	DBINHA (S) (D)	Converts BIN Data In S To Hexadecimal ASCII Code And Stores The Result In D.
DBINHAP	DBINHAP (S) (D)	Converts BIN Data In S To Hexadecimal ASCII Code And Stores The Result In D.

Conversion (HEX ASCII -> BIN)

Instruction	Type of Input	Note
HABIN	HABIN (S) (D)	Converts Hexadecimal ASCII COde In S To 16 Bit BIN Data And Stores The Result In D.
HABINP	HABINP (S) (D)	Converts Hexadecimal ASCII COde In S To 16 Bit BIN Data And Stores The Result In D.
DHABIN	DHABIN (S) (D)	Converts Hexadecimal ASCII Code In S To 32 BIt BIN Data And Stores The Result In Device D.
DHABINP	DHABINP (S) (D)	Converts Hexadecimal ASCII Code In S To 32 BIt BIN Data And Stores The Result In Device D.

Conversion (BCD -> ASCII)

Instruction	Type of Input	Note
BCDDA	BCDDA (S) (D)	Converts 4 Digits BCD Data In S To Decimal ASCII Code And Stores The Result In Device D.
BCDDAP	BCDDAP (S) (D)	Converts 4 Digits BCD Data In S To Decimal ASCII Code And Stores The Result In Device D.
DBCDDA	DBCDDA (S) (D)	Converts 8 Digits BCD Data In S To Decimal ASCII Code And Stores The Result In Device D.
DBCDDAP	DBCDDAP (S) (D)	Converts 8 Digits BCD Data In S To Decimal ASCII Code And Stores The Result In Device D.

Conversion (Floating decimal point, XP)

Instruction	Type of Input	Note
FLT	FLT (S) (D)	Converts 16-bit BIN data designated by S to floating decimal point real number, and stores at device number designated by D .
FLTP	FLTP (S) (D)	Converts 16-bit BIN data designated by S to floating decimal point real number, and stores at device number designated by D .
DFLT	DFLT (S) (D)	Converts 32-bit BIN data designated by S to floating decimal point real number, and stores at device number designated by D
DFLTP	DFLTP (S) (D)	Converts 32-bit BIN data designated by S to floating decimal point real number, and stores at device number designated by D
INT	INT (S) (D)	Converts the floating decimal point real number designated at S into BIN 16-bit data and stores it at the device number designated at D
INTP	INTP (S) (D)	Converts the floating decimal point real number designated at S into BIN 16-bit data and stores it at the device number designated at D
RAD	RAD (S) (D)	Converts units of angle size from angle units designated by S to radian units, and stores result at device number designated by D.
RADP	RADP (S) (D)	Converts units of angle size from angle units designated by S to radian units, and stores result at device number designated by D.
DEG	DEG (S) (D)	Converts Unit of angle size from radian units designated by S to angles, and stores result at device number designated by D.
DEGP	DEGP (S) (D)	Converts Unit of angle size from radian units designated by S to angles, and stores result at device number designated by D.
EMOV	EMOV (S) (D)	This is used to transfer the Floating-point data in the device assigned to S to the device assigned to D.
EMOVP	EMOVP (S) (D)	This is used to transfer the Floating-point data in the device assigned to S to the device assigned to D.

Decode / Encode

Instruction	Type of Input	Note
DECO	DECO (S) (D) (n)	Decodes Lower n Bits In S And Sets The Contact Corresponding To Result Of Device D.
DECOP	DECOP (S) (D) (n)	Decodes Lower n Bits In S And Sets The Contact Corresponding To Result Of Device D.
ENCO	ENCO (S) (D) (n)	Encodes The Uppermost Bit Location Which Is Set As 1 In 2^n Of S And Stores The Result In D In Numerical Value Data.
ENCOP	ENCOP (S) (D) (n)	Encodes The Uppermost Bit Location Which Is Set As 1 In 2^n Of S And Stores The Result In D In Numerical Value Data.

7 Segment

Instruction	Type of Input	Note
SEG	SEG (S) (D)	Decodes n Pieces Of Number From Start Bit In S As 7 Segment By The Set Format And Stores The Result In D.
SEGP	SEGP (S) (D)	Decodes n Pieces Of Number From Start Bit In S As 7 Segment By The Set Format And Stores The Result In D.

Union / Disunion

Instruction	Type of Input	Note
DIS	DIS (S) (D) (n)	Stores n(n=1 Means 4 Bits) Pieces Of Numerical Value Data From S In Lower Bit As Much As n From D Each.
DISP	DISP (S) (D) (n)	Stores n(n=1 Means 4 Bits) Pieces Of Numerical Value Data From S In Lower Bit As Much As n From D Each.
UNI	UNI (S) (D) (n)	Combines Each Lower 4 Bits Of n(n=1 Means 4 Bits) Pieces Of Data In S, And Stores the Result In Device D.
UNIP	UNIP (S) (D) (n)	Combines Each Lower 4 Bits Of n(n=1 Means 4 Bits) Pieces Of Data In S, And Stores the Result In Device D.

BIT

Instruction	Type of Input	Note
TEST	TEST (S1) (S2) (D)	Stores Bit Of The Assigned Order Among Data Bits In S1. If The Result Is 1, Sets. If 0, Resets.
TESTP	TESTP (S1) (S2) (D)	Stores Bit Of The Assigned Order Among Data Bits In S1. If The Result Is 1, Sets. If 0, Resets.
DTEST	DTEST (S1) (S2) (D)	Stores The Bit Of Order Assigned to S2 In Double-Word Data Bit Of S1 In D. If It Is 1, Sets. If 0, Resets.
DTESTP	DTESTP (S1) (S2) (D)	Stores The Bit Of Order Assigned to S2 In Double-Word Data Bit Of S1 In D. If It Is 1, Sets. If 0, Resets.
BSET	BSET (D) (n)	Sets nth Bit In Data Bits In Device D.
BSETP	BSETP (D) (n)	Sets nth Bit In Data Bits In Device D.
BRST	BRST (D) (n)	Resets nth Bit in Word Data Bits In Device D.
BRSTP	BRSTP (D) (n)	Resets nth Bit in Word Data Bits In Device D.
BITMOV	BITMOV (S) (D) (n)	Sends the data in the device assigned to S as much as n bits from the start device number in the device assigned to D.
BITMOVP	BITMOVP (S) (D) (n)	Sends the data in the device assigned to S as much as n bits from the start device number in the device assigned to D.
ANDBT	ANDBT (S1) (S2)	AND-Operates the bit of the order assigned to S2 in the word device data assigned to S1 and Contact A.
ANDBTI	ANDBTI (S1) (S2)
LDBT	LDBT (S1) (S2)	LD-Operates the bit of the order assigned to S2 in the word device data assigned to S1 and Contact A.
LDBTI	LDBTI (S1) (S2)
ORBT	ORBT (S1) (S2)	OR-Operates the bit of the order assigned to S2 in the word device data assigned to S1 and Contact A.
ORBTI	ORBTI (S1) (S2)
SUM	SUM (S) (D)	Counts Number Of Bit Data Which Are Set As 1 In Data Of S And Stores The Number.
SUMP	SUMP (S) (D)	Counts Number Of Bit Data Which Are Set As 1 In Data Of S And Stores The Number.
DSUM	DSUM (S) (D)	Counts Number Of Bit Data Which Are Set As 1 In Double-Word Data Of S And Stores The Number.
DSUMP	DSUMP (S) (D)	Counts Number Of Bit Data Which Are Set As 1 In Double-Word Data Of S And Stores The Number.

TIME

Instruction	Type of Input	Note
DATE+	DATE+ (S1) (S2) (D)	Adds Hour, Minute And Second Data In S2 To Hour, Minute And Second Data In S1 Each Other, And Stores The Result In D In Due Order.
DATE+P	DATE+P (S1) (S2) (D)	Adds Hour, Minute And Second Data In S2 To Hour, Minute And Second Data In S1 Each Other, And Stores The Result In D In Due Order.
DATE-	DATE- (S1) (S2) (D)	Subtrats Hour, Minute And Second Data In S2 From Hour, Minute And Second Data In S1 Each Other, And Stores The Result In D In Due Order.
DATE-P	DATE-P (S1) (S2) (D)	Subtrats Hour, Minute And Second Data In S2 From Hour, Minute And Second Data In S1 Each Other, And Stores The Result In D In Due Order.
SECOND	SECOND (S) (D)	Converts Hour, Minute And Second Data In S To Second Data Each And Stores The Result In D.
SECONDP	SECONDP (S) (D)	Converts Hour, Minute And Second Data In S To Second Data Each And Stores The Result In D.
HOUR	HOUR (S) (D)	Converts Second Data In S To Hour, Minute And Second Data And Stores The Result In D In Due Order.
HOURP	HOURP (S) (D)	Converts Second Data In S To Hour, Minute And Second Data And Stores The Result In D In Due Order.
DATERD	DATERD (D)	Reads Year, Month, Day, Hour, Minute, Second And Day Of Week Data From CPU Clock Device And Stores Them In Device D In Due Order.
DATERDP	DATERDP (D)	Reads Year, Month, Day, Hour, Minute, Second And Day Of Week Data From CPU Clock Device And Stores Them In Device D In Due Order.
DATEWR	DATEWR (S)	Year, Month, Day, Hour, Minute, Second And Day Of Week Data In S Are Written In CPU Clock Device.
DATEWRP	DATEWRP (S)	Year, Month, Day, Hour, Minute, Second And Day Of Week Data In S Are Written In CPU Clock Device.

Timer

Instruction	Type of Input	Note
TON	TON (S) (t)	If Curren Value Is Increased And Reaches Set Value, Timer Contact Is Set.
TOFF	TOFF (S) (t)	When Input Condition Is Off, The Set Value Is Subtracted. If Current Value Reaches 0, Output Is Reset.
TMR	TMR (S) (t)	Though Current Value Is Increased And Input Is On-Off Reapeatly, If The Current Value Is Accumulated Whenever It Is On And Reaches Set Time, Timer Contact Is Set.
TMON	TMON (S) (t)	Though Output Is Set And Input Is Set-Reset Repeatly, If Current Value Is Subtracted Whenever It Is Set And Reaches 0, Timer Output Is Reset.
TRTG	TRTG (S) (t)	If Output Is Set And Current Value Is Subtracted To Reach 0, Output Is Reset. If Output Is Reset Before Current Value Is 0, Current Value Is Set Up As Set Value.

Counter

Instruction	Type of Input	Note
CTU	CTU (S) (t)	Adds One By One To Current Value Whenever Pulse Is Input. If Current Value Is Over Set Value, Sets Output And Counts Up To Maximum Of Counter.
CTD	CTD (S) (t)	Subtracts One By One From Set Value Whenever Rising Edge Is Input. If The Value Is 0, Sets Output.
CTUD	CTUD (S) (t)	Adds One By One Whenever Pulse Is Input To Up Terminal. Substracts One By One Whenever Pulse Is Input To Down Terminal. If Current Value Is Over Set Value, Sets Output.
CTR	CTR (S) (t)	Adds One By One Whenever Pulse Is Input. If The Value Reaches Set Value, Sets Output. If Input Signal Is On From Off, Current Value Is Increased From 0.

Read / Write

Instruction	Type of Input	Note
FROM	FROM (n1) (n2) (D) (n3)	Reads n3 Pieces Of Word Data In User Program Memory n2 Of Optional Card n1(SLot Number) And Stores The Result In D.
FROMP	FROMP (n1) (n2) (D) (n3)	Reads n3 Pieces Of Word Data In User Program Memory n2 Of Optional Card n1(SLot Number) And Stores The Result In D.
DFRO	DFRO (n1) (n2) (D) (n3)	Reads n3 Pieces Of Double-Word Data In User Program Memory n2 Of Optional Card n1(Slot Number) And Stores Them In Device D.
DFROP	DFROP (n1) (n2) (D) (n3)	Reads n3 Pieces Of Double-Word Data In User Program Memory n2 Of Optional Card n1(Slot Number) And Stores Them In Device D.
TO	TO (n1) (n2) (S) (n3)	Writes n3 Pieces Data In S To User Program Memory n2 Of Opetional Card n1(Slot Numer).
TOP	TOP (n1) (n2) (S) (n3)	Writes n3 Pieces Data In S To User Program Memory n2 Of Opetional Card n1(Slot Numer).
DTO	DTO (n1) (n2) (S) (n3)	Writes n3 Pieces Of Double-Word Data In S To User Program Memory n2 Of Optional Card n1(Slot Number).
DTOP	DTOP (n1) (n2) (S) (n3)	Writes n3 Pieces Of Double-Word Data In S To User Program Memory n2 Of Optional Card n1(Slot Number).
FREAD	FREAD (n1) (n2) (D) (n3) (n4)	Read n3 words of data from the address designated by n2 ofthe system memory of the special function module designated by n1. Then, stores the data in the area starting from the device designated by D. The result of instruction is stored to the device designated by n3.
FREADP	FREADP (n1) (n2) (D) (n3) (n4)	Read n3 words of data from the address designated by n2 ofthe system memory of the special function module designated by n1. Then, stores the data in the area starting from the device designated by D. The result of instruction is stored to the device designated by n3.
FWRITE	FWRITE (n1) (n2) (D) (n3) (n4)	Write n3 words of data from the device designated by D to the area starting from the address designated by n2 of the system memory of the special function module designated by n1.
FWRITEP	FWRITEP (n1) (n2) (D) (n3) (n4)	Write n3 words of data from the device designated by D to the area starting from the address designated by n2 of the system memory of the special function module designated by n1.

Communication

Instruction	Type of Input	Note
SND	SND (Slot)(S)(Size)(Result)	Transmits Data In Device Of Master Atation To Device Of Slave Station.
SNDP	SNDP (Slot)(S)(Size)(Result)	Transmits Data In Device Of Master Atation To Device Of Slave Station.
RCV	RCV (Slot)(D)(Size)(Result)	Reads And Brings Data In Slave Station To Device Of Master Station.
RCVP	RCVP (Slot)(D)(Size)(Result)	Reads Data In Slave Station To Device Of Master Station.

Communication (SPC Program)

Instruction	Type of Input	Note
RECV	RECV (PID) (F_Name) (Result)	Compares the data received from master station with the data(F_Name) set up by Special Function Program(PID), storing them in the assigned device.
RECVP	RECVP (PID) (F_Name) (Result)	Compares the data received from master station with the data(F_Name) set up by Special Function Program(PID), storing them in the assigned device.
SEND	SEND (PID) (F_Name) (Result)	Sends the data(F_Name) set up by Special Function Program(PID) from master station to the device of slave station.
SENDP	SENDP (PID) (F_Name) (Result)	Sends the data(F_Name) set up by Special Function Program(PID) from master station to the device of slave station.

Watch Dog Time

Instruction	Type of Input	Note
WDT	WDT	Resets Watch Dog Timer While Operating Program.
WDTP	WDTP	Resets Watch Dog Timer While Operating Program.

Carry

Instruction	Type of Input	Note
STC	STC	If Input Condition Is On, Sets Carry Flag.
CLC	CLC	If Input Condition Is ON, Resets Carry Flag.

Refresh

Instruction	Type of Input	Note
RFS	RFS (S) (n)	Refreshes n Pieces Of Device Which Are Assigned To S For One Scan.
RFSP	RFSP (S) (n)	Refreshes n Pieces Of Device Which Are Assigned To S For One Scan.

PID

Instruction	Type of Input	Note
PIDCAL	PIDCAL (S)	Assigns Device Where Result Value Of PID Operation IS Stored As S.
PIDINIT	PIDINIT (S)	Assigns Device Where The Set Value For PID Operation Is Stored As S.

Trigonometric (XP Series)

Instruction	Type of Input	Note
SIN	SIN (S) (D)	Calculates SIN (sine) value of angle designated at S and stores the operation result in the device number designated at D.
COS	COS (S) (D)	Performs COS (cosine) on angle designated by S and stores operation result at device number designated by D .
TAN	TAN (S) (D)	Performs tangent (TAN) operation on angle data designated by S , and stores operation result in device designated by D.
ASIN	ASIN (S) (D)	Calculates angle from sin value designated by S, and stores operation result at word device designated by D
ACOS	ACOS (S) (D)	Calculates angle from COS value designated by S, and stores operation result at word device designated by D
ATAN	ATAN (S) (D)	Calculates angle from tan value designated by S, and stores operation result at word device desig
BSIN	BSIN (S) (D)	Calculates the sin value of the designated value, and stores the sign of the operation result in the device at D, and the operation result in the device designated at D+1 and D+2.
BCOS	BCOS (S) (D)	Calculates the cos value of the designated value, and stores the sign of the operation result in the device at D, and the operation result in the device designated at D+1 and D+2.
BTAN	BTAN (S) (D)	Calculates TAN (tangent) value for value (angle) designated by S , and stores the sign for the operation result in the word device designated by D , and the operation result in the word device designated by D +1 and D +2.
BASIN	BASIN (S) (D)	Calculates angle from sin value designated by S, and stores operation result at word device designated by D
BACOS	BACOS (S) (D)	Calculates angle from COS value designated by S, and stores operation result at word device designated by D
BATAN	BATAN (S) (D)	Calculates angle from sin value designated by S, and stores operation result at word device designated by D

Exponent, Logarithm (XP Series)

Instruction	Type of Input	Note
SQR	SQR (S) (D)	Calculates square root of value designated at S , and stores the operation result in the device number designated at D .
EXP	EXP (S) (D)	Calculates exponent for value designated by S, and stores the result of the operation at the device designate by D
LOG	LOG (S) (D)	Calculates natural logarithm of value designated by S taking e as base, and stores operation results at device designated by D.
BSQR	BSQR (S) (D)	Store appointed data to area that is specified by D after square root arithmetic by S.
BDSQR	BDSQR (S) (D)	Store appointed data to area that is specified by D after square root arithmetic by S.

User Clock

Instruction	Type of Input	Note
DUTY	DUTY (n1) (n2) (D)	Turns scan designated by n1 ON for user timing block designated by D, and scan designated by n2 OFF.

Table

Instruction	Type of Input	Note
FPOP	FPOP (DEV) (TBL)	Find Last Data In Table
FINS	FINS (DEV) (TBL) (n)	Insert a Data In Table
FDEL	FDEL (DEV) (TBL) (n)	Delete a Data From Table
FIFR	FIFR (DEV) (TBL)	Read the oldest data from [TBL+1] and stores it at the device designated by [DEV]. After the execution of FIFR, the data in the table moves to the previous device and the last data will be zero. The number of data of the data table will be decreased.
FIFRP	FIFRP (DEV) (TBL)	Read the oldest data from [TBL+1] and stores it at the device designated by [DEV]. After the execution of FIFR, the data in the table moves to the previous device and the last data will be zero. The number of data of the data table will be decreased.
FIFW	FIFW (DEV) (TBL)	Stores the 16 bit data designated by [DEV] at the end of the data table designated by [TBL]. The number of data blocks stored at [TBL] will be increased.
FIFWP	FIFWP (DEV) (TBL)	Stores the 16 bit data designated by [DEV] at the end of the data table designated by [TBL]. The number of data blocks stored at [TBL] will be increased.

Redundant System

Instruction	Type of Input	Note
ATVP	ATVP	Swap Active Status in Redundant System

Scan program Enable / Disable

Instruction

Type of Input

Note

EPGM

EPGM (n)

Permit driving of scan program that correspond to ID that is established by n.

Change relevant scan program to Enable status in Disable status by DPGM command.

if Disable Program command is not inputed at Mode conversion, it is all Enable PBT states

DPGM

DPGM (n)

Permit driving of scan program that correspond to ID that is established by n.

Change relevant scan program to Enable status in Disable status by DPGM command.

if Disable Program command is not inputed at Mode conversion, it is all Enable PBT states

Occur random number

Instruction	Type of Input	Note
RND	RND (D)	Generates random number of from 0 to 32767, and stores at device designated by D
SRND	SRND (D)	Updates random number series according to the 16-bit BIN data being stored in device designated by S.

Scale

Instruction	Type of Input	Note
SCL	SCL (S) (D) (P) (n)	Converts signed binary data into signed binary data according to Scale parameter table .
SCLP	SCLP (S) (D) (P) (n)	Converts signed binary data into signed binary data according to Scale parameter table .

Position (CP, XP)

Instruction	Type of Input	Note
ABRST1	ABRST1 (Base/Slot) (S) (D)
ABRST2	ABRST2 (Base/Slot) (S) (D)
ABRST3	ABRST3 (Base/Slot) (S) (D)
ABRST4	ABRST4 (Base/Slot) (S) (D)
PSTRT1	PSTRT1 (Base/Slot) (S) (D)
PSTRT2	PSTRT2 (Base/Slot) (S) (D)
PSTRT3	PSTRT3 (Base/Slot) (S) (D)
PSTRT4	PSTRT4 (Base/Slot) (S) (D)
TEACH1	TEACH1 (Base/Slot) (S) (D)
TEACH2	TEACH2 (Base/Slot) (S) (D)
TEACH3	TEACH3 (Base/Slot) (S) (D)
TEACH4	TEACH4 (Base/Slot) (S) (D)
PFWRT	PFWRT (Base/Slot) (S) (D)
PINT	PINT (Base/Slot) (S) (D)

etc

Instruction	Type of Input	Note
;	; (notes)	Shows Description.
DESCI	DESCI (notes)	Shows Description.
NOP	NOP	As No Operation Instruction, Does Not Influence Operation Result Of The Corresponding Circuit.