Performance Specifications(CM1 Redundancy)
- CIMON (Unlicensed)
Item | Specification | |
CM1-XP1S | ||
Program Control Method | Repetitive operation, Stored program (ROM mode), Periodic operation | |
I/O Control Method | Scan synchronous batch processing system (I/O refresh), Indirect method, Direct method by instruction | |
Program Language | IL (Instruction List), LD (Ladder Diagram), FBD (Function Block Diagram), FBD Extension | |
SFC (Sequential Function Chart) | ||
Number of Instruction | Basic Instruction: 60, Application instruction: 480 | |
Data Processing | LD | 0.028 μs/Step |
Floating-point Arithmetic | +, -, x, / : 0.4 μs/Instruction | |
Program Memory | 7 MByte (Upload, Parameter, System) | |
Number of Program Blocks | Max 128, up to 65,530 steps per block (PID) | |
Number of I/O | 8,192 | |
Number of I/O Devices | Input: 131,072 points, Output: 131,072 points | |
Supporting Programs | LD | Scan, Subroutine, Initialize (COLD), Initialize (HOT), Periodic interruption |
Special Configuration | Initializing special card, PID control, Thermistor setting, Loadcell setting, I/O Input module filter setting | |
Communication | User protocol (Serial), User protocol (Ethernet), MODBUS | |
SFC | SFC Program | |
Periodic Interruption | Maximum 15, cycle setting (10–60,000 ms, Unit:10 ms), Priority setting (0–14) | |
Base Expansion | Maximum 16, Ring topology | |
Max. Distance | Electricity (100 m) | |
Redundancy | Available | |
Operation modes | LOCAL/Remote (RUN, STOP, PAUSE) | |
Restarting | Cold, hot restart | |
Self-Diagnosis | Monitoring delay of processing, Problems of memory, I/O, Battery, Power error | |
Data Preservation Against Power Failure | K device and conservation (latch) in M, L, T, C, S, D devices | |
Watch Dog Timer (WDT) | Maximum 5000 ms (Unit: 10 ms) | |
Timer | On delay, Off delay, Addition, Monostable, Retriggerable | |
Counter | UP, DOWN, UP/DOWN, RING COUNTER, CC (Current value)/CS (Setting value) No limitation on number of points | |
PID | 32 Channels, Auto-Tuning | |
Communication Channels | USB | USB 2.0 Mini-B: For loader protocol |
Serial | RS-232C (Maximum 115,200 bps): CICON Loader, CIMON-HMI, MODBUS RTU Slave | |
Ethernet | Expanded :10/100Base -T/TX *Built-in Ethernet: Not available | |
Event Log | Maximum 100 (Power, Mode, Error) | |
Firmware Upgrade | Available | |
Power | 5 V DC, 220 mA | |
Weight | 138 g | |
Floating-point Arithmetic | Supports instructions for floating-point arithmetic | |
Capacity of Scan Program | 128k Step | |
Device Memory | X | 8,192 |
Y | 8,192 | |
M | 16,000 | |
K | 16,000 | |
L | 16,000 | |
F | 2,048 | |
T | 4,096 (Select between 10 ms and 100 ms) | |
C | 4,096 | |
S | 100 States * 100 set (00.00–99.99) | |
D | 32,000 Words | |
Z | 1,024 Words | |
Q | 512 Words | |
R | 16 Words | |
Items | Specification | |
CM1-XP1R | ||
Program Control Method | Repetitive operation, Stored program (ROM mode), Periodic operation | |
I/O Control Method | Scan synchronous batch processing system (I/O refresh), Indirect method, Direct method by instruction | |
Program Language | IL (Instruction List), LD (Ladder Diagram), FBD (Function Block Diagram) | |
Number of Instruction | Basic Instruction: 60, Application instruction: 480 | |
Data Processing | LD | 0.028 μs/Step |
Floating-point Arithmetic | +, -, x, / : 0.4 μs/Instruction | |
Program Memory | 7 MByte (Upload, Parameter, System) | |
Number of Program Blocks | Max 128, up to 65,530 steps per block (PID) | |
Number of I/O | 8,192 (Max 12,288) | |
Number of I/O Devices | Input: 131,072 points, Output: 131,072 points | |
Supporting Programs | LD | Scan, Subroutine, Initialize (COLD), Initialize (HOT), Periodic interruption |
Special Configuration | Initializing special card, PID control, Thermistor setting, Loadcell setting, I/O input module filter setting | |
Communication | User protocol (Serial), User protocol (Ethernet), DNP3, Fieldbus, MODBUS TCP/RTU Master, Ethernet High-speed link, CIMON-NET Master/Slave, Public network IP setting | |
OPC UA Server | - | |
SFC | - | |
Periodic Interruption | Maximum 15, Cycle setting (10–60,000 ms, Unit:10 ms), priority setting (0–14) | |
Base Expansion | Maximum 16, 10Base-T | |
Max. Distance | Electricity (100 m) | |
Redundancy | Available | |
Operation Modes | LOCAL/Remote (RUN, STOP, PAUSE) | |
Restarting | Cold, hot restart | |
Self-Diagnosis | Monitoring delay of processing, Problems of memory, I/O, Battery, Power error | |
Data Preservation Against Power Failure | K device and conservation (latch) in M, L, T, C, S, D devices | |
Watch Dog Timer (WDT) | Maximum 5000 ms (Unit: 10 ms) | |
Timer | On delay, Off delay, Addition, Monostable, Retriggerable Cycle: either 10 or 100 ms TC (Current value)/TS (Setting value) | |
Counter | UP, DOWN, UP/DOWN, RING COUNTER, CC (Current value)/CS (Setting value) No limitation on number of points Count range: -32,768–+32,767 | |
PID | 32 Channels, Auto-Tuning | |
Communication Channels | USB | USB 2.0 B Type: For loader protocol |
Serial | RS-232C (Maximum 38,400 bps): CICON Loader/Type: RJ11 | |
Ethernet | - | |
Event Log | Power, Mode, Error | |
Firmware Upgrade | - | |
Power | 5 V DC, 315 mA | |
Weight | 157 g | |
Floating number Arithmetic | Supports instructions for floating-point arithmetic | |
Capacity of Scan Program | 128k Step | |
Device memory | X | 8,192 |
Y | 8,192 | |
M | 16,000 | |
K | 16,000 | |
L | 16,000 | |
F | 2,048 | |
T | 4,096 (Select between 10 ms and 100 ms) | |
C | 4,096 | |
S | 100 States * 100 set (00.00–99.99) | |
D | 32,000 Words | |
Z | 1,024 Words | |
Q | - | |
R | 16 Words | |
Item | CM1-SPR | |
Input | Rated Voltage | AC 88–264 V |
Current | 1.8 A (110 V) 0.95 A (220 V) | |
Inrush Current | 50 A Peak | |
Efficiency | 65% | |
Permissible Instantaneous Power Failure Time | 10 ms | |
Output | Voltage (Current) | +24 V (0.3 A) +5.5 V (3.5 A) +15 V (0.5 A) -15 V (0.3 A) |
Operation Indication | LED is ON when output voltage is normal. | |
Items | CM1-RPW | |
Status Output (A_OK, B_OK, A_NG, B_NG) | Output Type | TR Sink Type |
Max Output Current | 0.5 A/Point | |
Rated Input Voltage | DC 24 V | |
Status Output (24V IN) | Rated Input Voltage | DC 24 V |
Max Input Current | 0.8 A | |
Power Coupler Input (AIN / BIN) | Rated Input Voltage | DC 24 V |
Power Coupler Output (24V OUT) | Rated Input Voltage | DC 24 V |
Max Input Current | 8 A | |
Operation Indication | LED is ON when the operation is normal. | |
Isolation Type | Photocoupler isolation | |
Items | CM1-RC10A |
Interface | 100 BASE –TX |
Data Transmit Speed | 100 Mbps |
Max. Distance | 100 m |
Protocol | CIMON Redundancy Protocol |
Cable Standard | UTP/STP Category5, Twisted pair cable |
Items | CM1-RM01B |
Primary/Secondary Switch | Toggle type 2-position (Up: primary, Down: secondary) |
Active/Back up Switching Switch | Push-button switch |